what is arduino
Showing 85–97 of 97 results
-
Arduino, Arduino Boards & Components, Development Kits
TTP 223 Touch Sensor Module Touch Sensor
?Key Features :
-
- Modes?Toggle or switch.
- Operating current @VDD=3V, no-load, SLRFTB=1.
- The response time max about 60mS at fast mode, 220mS at low power mode @VDD=3V.
- Sensitivity can adjust by the capacitance(0~50pF) outside.
- Have two kinds of sampling length by pad option(SLRFTB pin).
- Stable touching detection of the human body for replacing traditional direct switch key.
- Provides Fast mode and Low Power mode selection by pad option(LPMB pin).
- Provides direct mode toggle?mode by pad option(TOG pin), the open-drain mode by bonding option, OPDO pin is an open-drain output, Q pin is CMOS output.
- All output modes can be selected active high or active low by pad option(AHLB pin).
- Have the maximum on-time 100sec by pad option(MOTB pin).
- Have external power-on reset pin(RST pin).
- After power-on have about 0.5sec stable-time, during the time do not touch the keypad, And the function is disabled.
- Auto calibration for life.
- Re-calibration period is about 4.0sec when the key has not to be touched.
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
Universal Wheel For Smart Car Robot Omni Wheel
-8%
Arduino, Arduino Boards & Components, Development KitsUniversal Wheel For Smart Car Robot Omni Wheel
?Key Features :
- Holder material:12mm cold-roll steel sheets,blue Zinc plating
Wheel material: White nylon PP material,wear resisting & handy
Wheel diameter: 24mm
Wheel face width: 13mm
Mounting height: 32mm
Plate size: 38*32（mm）
Mounting hole diameter:4mm
Mounting hole center distance:30*24（mm）
Single wheel load:10kg
Single wheel weight:0.04kg
SKU: n/a - Holder material:12mm cold-roll steel sheets,blue Zinc plating
-
Arduino, Arduino Boards & Components, Development Kits
UNO orginal 328+16U2-without Wire
Key Features:
- NEW IMPROVEMENT: Clear prints on the female header connector, more precise and easier to use the wire.
- The ELEGOO UNO R3 BOARD now uses an ATMega16U2 instead of the ATMega8U2 chip. Faster transfer rates and more memory.
- Control using ATMEL ATMEGA328P chip(the same with Arduino UNO R3)
- 100% compatible with the Arduino IDE and RoHS Compliant
- The Uno board can be powered via the USB connection.
- The Uno board can be powered with an external power supply.
- Excellent welding and production quality to make sure satisfied customer experience
- The RX and TX LEDs on the board will flash when data is being transmitted via the USB-to-serial chip and USB connection to the computer.
- We have always cared about the customer experience and improve the product function details.
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Voltage Sensor Dc 0 To 25v Voltage Sensor
?Key Features :
-
- Dimensions: 28 x 14 x 13 mm(LxWxH).
- Weight: 4 gm.
- Input Voltage range: DC0 to 25 V
- Voltage detection range: DC 0.02445 V to 25 V
- Analog Voltage resolution : 0.00489 V
- Output Interface : ?+ ? connected 5/3.3V, ?-? connected GND, ?s? connected Arduino AD pins
- DC input interface: red terminal positive with VCC, negative with GND
- You can also use the IICLCD1602 LCD to display voltage.
- By 3P connector, connect this module with the expansion of board Arduino, not only makes it easier for you to detect voltage battery.
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
W1209 DC12V Digital Thermostat Temperature Controller (Incubator Controller)
-4%
Arduino, Arduino Boards & Components, Development KitsW1209 DC12V Digital Thermostat Temperature Controller (Incubator Controller)
?Key Features :
-
-
- Temperature Control Range: Minus 50 to 110 C
- Resolution at -9.9 to 99.9: 0.1 C
- Resolution at all other temperatures: 1 C
- Measurement Accuracy: 0.1 C
- Control Accuracy: 0.1 C
- Refresh Rate: 0.5 Seconds
- Input Power (DC): 12V
- Measuring Inputs: NTC (10K 0.5%)
- Waterproof Sensor: 0.5M
- Output: 1 Channel Relay Output, Capacity: 10A
Best Online Shopping website for W1209 Temperature Controller Incubation Thermostat. Here you get W1209 Temperature Controller Thermostat at a reasonable price in Karachi, Lahore, Islamabad, Rawalpindi, Peshawar, Multan, Faisalabad and all over Pakistan.
-
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
W3001 Digital Temperature Controlle Thermostat, AC 220V Thermometer Controller
-2%
Arduino, Arduino Boards & Components, Development KitsW3001 Digital Temperature Controlle Thermostat, AC 220V Thermometer Controller
?Key Features :
-
-
- ABS flame retardant housing is avirulent and environmental protective, long service life and will not discolor or be out of shape
- Wide temperature control range from -50? to 110? and high-temperature control precision of 0.1?
- Can be installed directly or embedded in industrial control equipment panel, convenient and quick
- Widely used in the hatching area, equipment case, air conditioning system, temperature control protection, and other fields
- The probe used stainless steel material shell and resin sealing treatment, waterproof and does not rust
-
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
Water Flow Sensor
?Key Features :
-
- Model: YF-S201
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Liters/Minute
- Working Temperature range: -25 to +80?
- Working Humidity Range: 35%-80% RH
- Accuracy: ?10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Liter: 450
- Durability: minimum 300,000 cycles
- Cable length: 15cm
- 1/2? nominal pipe connections, 0.78? outer diameter, 1/2? of thread
- Size: 2.5? x 1.4? x 1.4?
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
Water Level Sensor
?Key Features :
-
-
Operating voltage: DC3-5V
-
Operating current: less than 20mA
-
Sensor Type: Analog
-
Detection Area: 40mmx16mm
-
Production process: FR4 double-sided HASL
-
Operating temperature: 10?-30? Humidity: 10% -90% non-condensing
-
Dimensions: 60mmx20mm
-
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
Water Pump 5V
?Key Features :
- Operating Current : 130 ~ 220mA
- Operating Voltage : 2.5 ~ 6V
- Flow Rate : 80 ~ 120 L/H
- Maximum Lift : 40 ~ 110 mm
- Driving Mode : DC, Magnetic Driving
- Continuous Working Life : 500 hours
- Material : Engineering Plastic
- Outlet Outside Diameter : 7.5 mm
- Outlet Inside Diameter : 5 mm
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
XL-4015 Adjustable Dc To Dc Step Down 5a Buck Converter With Heatsink
-4%
Arduino, Arduino Boards & Components, Development KitsXL-4015 Adjustable Dc To Dc Step Down 5a Buck Converter With Heatsink
?Key Features :
- Input voltage range?4?38VDC(Note: input voltage not exceeding 38V).
- Output voltage range?1.25-36VDC adjustable.
- Output current:?0-5A.
- High efficiency up to 96%.
- Output power:?75W.
- Built-in thermal shutdown function
- Built-in current limit function
- In-Built output short protection function
- Input reverse polarity protection: None (if required, the high current diode in series with the input).
- Power Indicator:?Yes
- Short circuit protection: Yes (limit current 8A)
- Overtemperature protection: (automatically shut off the output after overtemperature)
- Input reverse polarity protection: No, (if necessary, please enter the string into the high current diode)
- Installation:?two 3mm screws
- Dimensions(LxWxH): 54 x 23 x 15 mm
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
XL-6009 Dc To Dc Boost Converter Voltage Booster
-3%
Arduino, Arduino Boards & Components, Development KitsXL-6009 Dc To Dc Boost Converter Voltage Booster
?Key Features :
- Module properties: unfenced step-up (BOOST)
- The input voltage: 3-32 v
- Continuous adjustable output voltage: 5v-35 v
- Input current: 4 a (Max), no-load 18 ma
- Module size: 44.7 (mm) x21.7 (mm)
- Input mode: IN + input level is, the IN ? negative input
- Output mode: OUT + output level is, the OUT ? output is negative
- Conversion efficiency: < 94% (the lower the pressure difference, the greater the efficiency)
- Output ripple: 50 mv (the bigger the higher the voltage, current and ripple)
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
ZB2L3 Battery Capacity Tester External Load Discharge Type Module
-3%
Arduino, Arduino Boards & Components, Development KitsZB2L3 Battery Capacity Tester External Load Discharge Type Module
?Key Features :
- Power supply voltage: DC4.5-6V (micro USB connector)
- Operating current: Less than 70mA
- Discharge voltage: 1.00V-15.00V, 0.01V resolution
- Termination voltage range: 0.5-11.0V
- Supported current: Maximum 3.000A, 0.001A resolution
- Maximum voltage measurement error: 1% + 0.02V
- Maximum current measurement error: 1.5% ? 0.008A
- Maximum battery capacity range: 9999Ah (1Ah = 1000mAh) greater value is switched by shifting the decimal point, when it is less than 10Ah will display X.XXX, up to 10Ah or more will display XX.XX, and so on.
- Board size: 50 x 37mm
- Finished size: 50 x 37 x 17mm (L x W x H maximum position size, contains copper foot height)
- Board net weight: 28g (including pillars)
- Resistor weight: about 27g (including cable)
SKU: n/a
