Development Kits

 Key Features :

1. – Diameter:68mm
2. – Width:26mm
3. – Other size refer to below picture
4. – Weight:40g/pc

 Key Features :

1. High-quality materials: These jumpers are made of excellent copper-coated material with outstanding conductivity and transmission performance, easily reshaped for connection testing.
2. Easy to use: Each breadboard jumper has stripped ends for easy insertion into the breadboard, connecting via pin connections without soldering.
3. Easy to store: All jumper wires are neatly stored in the included plastic sorting box, which helps you keep the jumpers organized for easy identification and use.
4. Broad application range: These flexible wire bridges for breadboards and lab boards are ideal for use with plugboards, prototypes, LED strips, test circuits, and more. They are widely used in electronic projects for connections and rapid circuit testing.
5. Wide variety: The set includes a diverse range of wire bridges in the most common lengths, allowing you to complete any project successfully.

 Key Features :

1. • Ultra-thin design & adhesive backing provides easy integration to any project
   • Excellent price-performance ratio
   • Easy communication with any microcontroller
   • 5 pins 2.54mm pitch connector, 4x 4type 16 keys.
   • Sticker can peel off for adhesive mounting.
   • Used widely in industrial and home electronic equipments, instrument, etc.
   • This allows a microcontroller to ‘scan’ the 8 output pins to see which of the 16 buttons is being pressed.

 Key Features :

1. Input: 5 V 1A
2. Charging and discharging indication
3. Size: approximately 22mm * width 17mm * thickness 11mm
4. Internally installed charging and discharging power MOS
5. Preset 4.2V charging voltage, precision ±1%
6. Max 8uA standby current
7. Integration charging management and discharging management
8. Intelligent temperature control and overtemperature protection
9. Integration output overvoltage protection, short circuit protection, overload protection
10. Integration overcharging and over-discharging protection
11. Support trickle mode and zero voltage charging
12. Output: 5 V 1A
13. Lithium voltage: 3 v-4.3 V
14. Ports: Micro USB Android port. USB port output
15. When charging: red light flashing Full charged: red light for a long time
16. Has protection functions, protects from overcharger/overload (supports charger and discharger at the same time)

 Key Features :

1. Piezo sounders contain a piezoelectric vibration plate (also known as a piezo element) within a molded case.
2. Sound is emitted when a voltage is applied and the piezo element inside the case vibrates.
3. Piezo buzzers generally use less current.
4. Have a higher sound output and a wider operating voltage.
5. Buzzers and Sounders can also be split into Audio Indicators and Audio Transducers.

 Key Features :

1. • Voltage – Supply : 3.3 V/ 5V.
   • Interface : I²C, SPI.
   • Sensing Range : ±2g, 4g, 8g, 16g.
   • Sensitivity:
   • X : 28.6 LSB/g.
   • Y : 31.2 LSB/g.
   • Z : 34.5 LSB/g.
   • Sensor Type : Accelerometer 3 Axis.
   • Dimensions : 28 mm x 14 mm.
   • Weight : 10 gm.
   • Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V.
   • Free-Fall Detection.
   • Tap/Double Tap Detection.
   • Flexible interrupt modes mappable to either interrupt pin Measurement ranges selectable via serial command Bandwidth selectable via serial command
   • Wide temperature range (−40°C to +85°C).
   • 10,000 g shock survival.
   • Support 5V/3.3V voltage input, on-board RT9161 power chip, lower pressure drop faster than the 1117, faster load speed of response, very suitable for high-noise power supply environment.
   • User-selectable resolution
   • Fixed 10-bit resolution.
   • Full resolution, where resolution increases with g range, up to 13-bit resolution at ±16 g (maintaining 4 mg/LSB scale factor in all g ranges).

Key Features:

• The Nano is using the chips ATmega+328P and CH340, not FT232 as official Arduino, so pls. use the driver from our site.
• It is a smallest, complete, and breadboard friendly board. It has everything that Diecimila/Duemilanove has (electrically) with more analog input pins and onboard +5V AREF jumper.
• Nano’s got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, so users have more breadboard space. It’s got a pin layout that works well with the Mini or the Basic Stamp (TX, RX, ATN, GND on one top, power and ground on the other).
• The Nano can be powered via the Mini-B USB connection, 7-12V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.
• Learn Arduino Nano with ease: Our ELEGOO Nano Board is the perfect choice for beginners and experts alike, with tutorials available to help you get started.

 Key Features :

1. Stable and reliable chipset CP2102.
2. USB specification 2.0 compliant with full-speed 12Mbps.
3. Standard USB type A male and TTL 6pin connector.
4. 6pins for 3.3V, RST, TXD, RXD, GND & 5V.
5. Baud rates: 300 bps to 1.5 Mbps
6. Byte receive buffer; 640 byte transmit buffer.
7. Hardware or X-On/X-Off handshaking supported.
8. Event character support Line break transmission.
9. USB suspend states supported via SUSPEND pins.
10. Temperature Range: -40 to +85.
11. Size: 42mm X 15mm.
12. Weight: 4g

 Key Features :

1. 3 wire  0-100V Red LED digital voltmeter module panel meter
   • Sensing Voltmeter: 0-100V.
   • Power supply: DC4-30V
   • Measuring range: 0-100V.
   • Measurement accuracy: ±0.1%
   • Refresh rate: about 200ms
   • Display: 0.56 “digital tube
   • Color: Red
   • Operating current: Less than 8mA
   • Operating temperature: -10°C to 65°C
   • Input impedance:100K
   • Overall dimension: 48*29*26mm
   • Display LED color – Red