eph

?Key Features :

1. Build in ultra low noise linear LDO voltage regulator
2. Build-in on board filters, which reduce noise from motor and other high current electronics
3. All sensors connected to I2C bus
4. You can easily select two I2C address for MPU6050 by soldered jumper
5. Tri-Axis angular rate sensor (gyro) with a sensitivity up to 131 LSBs/dps and a full-scale range of ?250, ?500, ?1000, and ?2000dps
6. Tri-Axis accelerometer with a programmable full scale range of ?2g, ?4g, ?8g and ?16g
7. Digital Motion Processing? (DMP?) engine offloads complex MotionFusion, sensor timing synchronization and gesture detection
8. Embedded algorithms for run-time bias and compass calibration. No user intervention required
9. Power LED
10. Input Voltage: 2.3 ? 3.4V
11. Build in Logic level converter for I2C
12. Digital-output temperature sensor
13. Dimensions?20x16mm
14. Designed for 5V logic level

?Key Features :

1. Good sensitivity to Combustible gas in wide range
2. High sensitivity to LPG, Propane and Hydrogen
3. Long life and low cost
4. Simple drive circuit

Key Features :

1. 1. Stepper motor is known by its property to convert a train of input pulses into a precisely defined increment in the shaft position.
   2. This is a high-quality motor that can be used for a long time without stuck.
   3. It has a quite stable performance during work and will not lose step.
   4. Low noise and big torque, this is a great choice if you need a stepper motor.
   5. Stepper motor can be widely used for a 3D printer, CNC engraving machine, etc.

?Key Features :

1. 1. 1. 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire
      2. supported(except D0)
      3. 1 analog input(3.2V max input)
      4. Micro USB connection
      5. Use BRT (Bias Resistor Transistor), easier into flash mode.
      6. 30% increase in radiating area, more stable.
      7. Dimensions : 35 x 26 x 8 (LxWxH) mm.
      8. Weight: 10 gm.
      9. Board Color : Blue
      10. Compatible with Arduino
      11. Compatible with NodeMCU
      12. Compatible with MicroPython

?Key Features :

1. Product use: rain, rain sensor, can be used for all kinds of weather monitoring, and translated into output signals and AO.
   The sensor USES the high quality FR ? 04 double material, large area of 5.5 * 4.0 CM, treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance;
   The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 mA;
   With potentiometer sensitivity adjustment
   The working voltage of 3.3 V to 5 V
   The output format: digital switch output (0 and 1) and analog AO voltage output;
   Has a fixed bolt hole, convenient installation
   Small board PCB size: Approx. 3.2 cm x 1.5 cm
   The LM393, use of wide voltage comparator

?Key Features :

1. The main chip: ISD1820.
2. Dimensions : 43 x 34 x 11 (LxWxH) mm.
3. The working voltage: DC 3V-5V.
4. Loudspeaker: 8 Ohm, 0.5W.
5. An easy to use 10 seconds of voice recording.
6. High-quality, natural voice restored.
7. Can be used as propaganda module.
8. With looping, jog playback, single-pass play function.
9. Available single-chip control.
10. This module can directly drive a small speaker 8 ohm 0.5W.
11. Power supply : 3-5V, which can be accessed pin power.
12. Audio recording control mode: the key to control or microcontroller, IO has drawn the line of control.

?Key Features :

1. Model : KY-040.
2. Type : Incremental Encoder.
3. Cycles per revolution (CPR) : 20.
4. Working voltage : 0 ? 5V.
5. Material : PCB + Brass.
6. Weight : 10 gm.
7. Size : 32 x 19 x 30 mm.

?Key Features :

1. Tiny and lightweight with high output power. The servo can rotate approximately 180 degrees (90 in each direction) and works just like the standard kinds but smaller.
2. You can use any servo code, hardware, or library to control these servos.
3. Good for beginners who want to make stuff move without building a motor controller with feedback & gearbox, especially since it will fit in small places. It comes with 3 horns (arms) and hardware.

?Key Features :

1. • small size, easy to use;
   • low voltage, low power consumption;
   • high accuracy;
   • strong anti-jamming;
   • integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions.

?Key Features :

1. PCB installed inside of?aluminum alloy U disk?shell, portable, safe and reliable!
2. Interface definition?directly marked on the shell, clear, convenient and practical!
3. 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V
4. Shell characters using laser engraving, never fade off! Permanent clarity!
5. 500MA internal resettable fuse,?complete protection of your expensive computer motherboard!
6. Red and blue color LED indicator, allowing you to always observe ST-LINK V2 working condition!
7. With 4 DuPont line, so you can easily respond to different target board line order!
8. Use anti-static bag packaging.

?Key Features :

• Ceramics thermoelectric Cooler semiconductor module TEC1-12706
• Small module.
• Its work is characterized by side refrigeration and side fever.
• Hot and cold on both sides of the temperature difference of 68 degrees
• Connected to the 12-volt power supply cooling piece on both sides there will be the difference in temperature, side cold side of the heat, do not long power cooler radiator, otherwise, it will cause cooler internal overheating and burning.
• Quality tested cooling cells.
• Solid-state, vibration-free, noise-free.
• Simple to install and operate.
• Fitted with 6-inch insulated leads