tlt
Showing 169–196 of 220 results
-
Arduino, Arduino Boards & Components, Development Kits
Mini Digital Thermometer Hygrometer Temperature Humidity Meter Fy-11
-4%
Arduino, Arduino Boards & Components, Development KitsMini Digital Thermometer Hygrometer Temperature Humidity Meter Fy-11
Key Features :
- Measuring humidity and temperature.
- Large LCD display, easy for reading.
- Temperature unit is switchable.
- Desk-top placing or wall hanging, easy to use.
- Made of high-quality material.
- Widely used in indoor temperature and humidity measurement, apply in the lab, cold chain transport, warehousing and other occasions.
- Powered by 2 x 1.5v LR44 button cell.
- Comes with a probe that is easy to use.
- Perfect for use in incubators, brooders, homebrew room at any other place, the monitoring of temperature and humidity required.
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
MPU 6050 3 Axis Digital Gyroscope Accelerometer Sensor Module
-3%
Arduino, Arduino Boards & Components, Development KitsMPU 6050 3 Axis Digital Gyroscope Accelerometer Sensor Module
Key Features :
- Build in ultra low noise linear LDO voltage regulator
- Build-in on board filters, which reduce noise from motor and other high current electronics
- All sensors connected to I2C bus
- You can easily select two I2C address for MPU6050 by soldered jumper
- Tri-Axis angular rate sensor (gyro) with a sensitivity up to 131 LSBs/dps and a full-scale range of ±250, ±500, ±1000, and ±2000dps
- Tri-Axis accelerometer with a programmable full scale range of ±2g, ±4g, ±8g and ±16g
- Digital Motion Processing™ (DMP™) engine offloads complex MotionFusion, sensor timing synchronization and gesture detection
- Embedded algorithms for run-time bias and compass calibration. No user intervention required
- Power LED
- Input Voltage: 2.3 – 3.4V
- Build in Logic level converter for I2C
- Digital-output temperature sensor
- Dimensions 20x16mm
- Designed for 5V logic level
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
MT3608 Mt3608 Booster Converter Power Module Dc-dc Step Up Module
-7%
Arduino, Arduino Boards & Components, Development KitsMT3608 Mt3608 Booster Converter Power Module Dc-dc Step Up Module
Key Features :
-
-
- It’s efficient up to 93%
- It can source a good amount of current
- It is an inexpensive converter module
- It’s simple to adjust to get your desired increase in voltage
- 4-bit or 8-bit MPU Interface
- Standard Type
- Works with almost any Microcontroller
-
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
N20 DC Gear Motor
Key Features :
- Motor size: 10*12 (N20 motor)
- Out Shaft diameter: 2.95mm (flat position: 2.45mm)
- Shaft length: 8mm
- Weight: 10g
- Rated load : 200 g.cm
- Working temperature: -10 degrees – 65 degrees
- Motor mounting position: horizontal or vertical
- Reduction ratio : 1:298
- Rated voltage: DC 5V
- Rated current : 36 MA
- Rated load speed: 50RPM
- Stall torque: 1 KG.cm
- Operating voltage range : DC3V-6V
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Nema17 4 Wire Stepper Motor Nema17 Stepper Motor
-4%
Arduino, Arduino Boards & Components, Development KitsNema17 4 Wire Stepper Motor Nema17 Stepper Motor
Key Features :
-
- Stepper motor is known by its property to convert a train of input pulses into a precisely defined increment in the shaft position.
- This is a high-quality motor that can be used for a long time without stuck.
- It has a quite stable performance during work and will not lose step.
- Low noise and big torque, this is a great choice if you need a stepper motor.
- Stepper motor can be widely used for a 3D printer, CNC engraving machine, etc.
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
Nodemcu Mini ESP8266 Wemos D1-Mini Wifi
Key Features :
-
-
- 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire
- supported(except D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Use BRT (Bias Resistor Transistor), easier into flash mode.
- 30% increase in radiating area, more stable.
- Dimensions : 35 x 26 x 8 (LxWxH) mm.
- Weight: 10 gm.
- Board Color : Blue
- Compatible with Arduino
- Compatible with NodeMCU
- Compatible with MicroPython
-
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
Orginal UNO starter kit
Key Features :
- 1 × Arduino Uno R3
- 1 × USB Cable for Arduino Uno and Arduino Mega
- 1 × Arduino Infrared Remote
- 1 × IR Transmitter LED 5mm Infrared Transmitter
- 1 × KY-028 Ky028 Temperature Sensor Module
- 20 × 20cm Pin to Pin 1 Pin Jumper Wire Dupont Line (Arduino Male to Male)
- 20 × 20cm Pin to Hole 1 Pin Jumper Wire Dupont Line (Arduino Male to Female)
- 1 × MB102 Breadboard 830 Points Solderless Prototyping Breadboard
- 1 × 2.54mm Pitch 40 Pin Male Header
- 1 × 2.54mm Pitch 40 Pin Single Row Female Header Strip
- 1 × Towerpro Sg90 Sg 90 180 Degree Servo Motor
- 1 × 24BYJ High Torque Geared Stepper Motor
- 1 × DC 2V to 24V 5100 RPM High Torque Mini Micro Motor
SKU: n/a -
-
-
-
Arduino, Arduino Boards & Components, Development Kits
Proximity Sensor E18-D80NK Infrared Yellow NPN-NO with cable
-2%
Arduino, Arduino Boards & Components, Development KitsProximity Sensor E18-D80NK Infrared Yellow NPN-NO with cable
Key Features :
- Sensor Type: Inductive
- Sensing distance: 0.079″ (2mm)
- Output Type: NPN-NO, 3-Wire
- Response Frequency: 1.5kHz
- Shielding: Shielded
- Material: Nickel-Plated Brass
- Voltage: 10V ~ 40V
- Termination style: Cable leads
- Operating Temperature: -40°C ~ 85°C
- Package/case: Cylinder, Threaded – M12
- Ingress Protection: IP67
- Indicator: LED
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
PS2 Dual Axis Xy Analog Joystick Module
Key Features :
- Two independent Potentiometer: one for each axis ( X and Y)
- Auto return to the center position
- Low weight
- Cup-type Knob
- Compatible to interface with Arduino or with most microcontrollers
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Rain Drops Detection Sensor
Key Features :
- Product use: rain, rain sensor, can be used for all kinds of weather monitoring, and translated into output signals and AO.
The sensor USES the high quality FR – 04 double material, large area of 5.5 * 4.0 CM, treatment of nickel plating and surface, have fight oxidation, electrical conductivity, and life has more superior performance;
The comparator output, signal clean, good waveform, driving ability is strong, for more than 15 mA;
With potentiometer sensitivity adjustment
The working voltage of 3.3 V to 5 V
The output format: digital switch output (0 and 1) and analog AO voltage output;
Has a fixed bolt hole, convenient installation
Small board PCB size: Approx. 3.2 cm x 1.5 cm
The LM393, use of wide voltage comparator
SKU: n/a - Product use: rain, rain sensor, can be used for all kinds of weather monitoring, and translated into output signals and AO.
-
Arduino, Arduino Boards & Components, Development Kits
Recording And Playback Module (Isd1820) With On Board Mic And Loud Speaker
-3%
Arduino, Arduino Boards & Components, Development KitsRecording And Playback Module (Isd1820) With On Board Mic And Loud Speaker
Key Features :
- The main chip: ISD1820.
- Dimensions : 43 x 34 x 11 (LxWxH) mm.
- The working voltage: DC 3V-5V.
- Loudspeaker: 8 Ohm, 0.5W.
- An easy to use 10 seconds of voice recording.
- High-quality, natural voice restored.
- Can be used as propaganda module.
- With looping, jog playback, single-pass play function.
- Available single-chip control.
- This module can directly drive a small speaker 8 ohm 0.5W.
- Power supply : 3-5V, which can be accessed pin power.
- Audio recording control mode: the key to control or microcontroller, IO has drawn the line of control.
SKU: n/a -
Single/Full Color (RGB) Panels/Modules, SMD Screens & Tickers
Red P10 Single Color Outdoor DIP LED Module For Tickers
-15%
Single/Full Color (RGB) Panels/Modules, SMD Screens & TickersRed P10 Single Color Outdoor DIP LED Module For Tickers
Key Features
- Full outdoor: IP65
- Size (W x H): 320 x 160 mm (320 x 160cm), 12.6 x 6.3 Inch
- Resolution (W x H): 32 x 16 = 512
- HUB Signal: HUB12
- Volt: 5v DC
- Brightness: 5000 cdm (nits)
- LED: DIP 5 mm
- Accessories: Rubber seal, data wire, power cable
- Can work with control card: U6A, U6B, U60, W60, U61, U62, U64, U6BN, WLP-XUA2, WLP-XUB1, etc.
- Display can Show: Text, Animation word, Time, Count, Lunar calendar
- Support simple animation characters
- Click Here to Download HD-U6A Software HD2018
SKU: n/a -
Single/Full Color (RGB) Panels/Modules, SMD Screens & Tickers
Red P10 Single Color Outdoor SMD Module For Tickers
-10%
Single/Full Color (RGB) Panels/Modules, SMD Screens & TickersRed P10 Single Color Outdoor SMD Module For Tickers
Key Features
- Red P10 Single Color SMD Module For Tickers
- Full outdoor: IP64
- Size (W x H): 320 x 160 mm (320 x 160cm), 12.6 x 6.3 Inch
- Resolution (W x H): 32 x 16 = 512
- HUB Signal: HUB12
- Volt: 5v DC
- Brightness: 4500 cdm (nits)
- LED: DIP 5mm
- Accessories: Data Wire, Power Cable, 4-Magnets
- Can work with control card: U6A, U6B, U60, W60, U61, U62, U64, U6BN, WLP-XUA2, WLP-XUB1, etc.
- The display can Show: Text, Animation word, Time, Count, Lunar calendar
- Support simple animation characters
- Click Here to Download HD-U6A Software HD2018
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
SG90 Towerpro 180 Degree Servo Motor
Key Features :
- Tiny and lightweight with high output power. The servo can rotate approximately 180 degrees (90 in each direction) and works just like the standard kinds but smaller.
- You can use any servo code, hardware, or library to control these servos.
- Good for beginners who want to make stuff move without building a motor controller with feedback & gearbox, especially since it will fit in small places. It comes with 3 horns (arms) and hardware.
SKU: n/a -
Control Card, Single & Dual LED Controllers, SMD Screens & Tickers
Single Color Control Card HD-U6A with USB Port
-33%
Control Card, Single & Dual LED Controllers, SMD Screens & TickersSingle Color Control Card HD-U6A with USB Port
Key Features
- Support single color module
- Various conventional scanning methods
- Control range Single color resolution 320W*32H
- FLASH Capacity 1M Byte
- Communication Port U-Disk
- HUB Signal 2HUB12
- Program Quantity 1000pcs Programs
- 4 areas with separate zone, and separated special effects and border
- Display Showing TextAnimation wordTimeCountLunar calendar
- Can support” TextAnimationPicture, Time, Timing display
- Program border, area border, and Custom design border
- More than 40 kinds of text effects display
- Support simple animation characters
- Support for hollow fonts, strokes, and other fonts, etc.
- Support for regional text background settings
- support Excel form to add directly
- Clock function
- Support calendar, analog clock, lunar calendar
- Timing & countdown display
- Support for multiple time zones
- Automatic switch screens
- Brightness setting by Customer by time period regulation
- Brightness adjustment Support two modes of brightness adjustment
- Test button, click to switch screen test status
- HUB12 to connect the display
- Click Here to Download HD-U6A User Manual
- Click Here to Download HD-U6A Software HD2018
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Soil Moisture Sensor
Key Features :
- Operating voltage: 3.3V~5V
- Dual output mode,analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable
- Panel PCB Dimension: Approx.3cm x 1.5cm
- Soil Probe Dimension: Approx. 6cm x 3cm
- Cable Length: Approx.21cm
- Interface Description(4-wire):
- VCC: 3.3V-5V
- GND: GND
- DO: digital output interface(0 and 1)
- AO: analog output interface
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
SR04T Waterproof Ultrasonic Sensor Jsn-sr04t Distance
-1%
Arduino, Arduino Boards & Components, Development KitsSR04T Waterproof Ultrasonic Sensor Jsn-sr04t Distance
Key Features :
-
- small size, easy to use;
- low voltage, low power consumption;
- high accuracy;
- strong anti-jamming;
- integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions.
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
St-link V2 Programmer For STM8 and STM 32
Key Features :
- PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable!
- Interface definition directly marked on the shell, clear, convenient and practical!
- 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V
- Shell characters using laser engraving, never fade off! Permanent clarity!
- 500MA internal resettable fuse, complete protection of your expensive computer motherboard!
- Red and blue color LED indicator, allowing you to always observe ST-LINK V2 working condition!
- With 4 DuPont line, so you can easily respond to different target board line order!
- Use anti-static bag packaging.
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
TCRT5000 IR Sensor Module Line Tracking Line
-4%
Arduino, Arduino Boards & Components, Development KitsTCRT5000 IR Sensor Module Line Tracking Line
Key Features :
-
-
- sensor adopts TR5000, high sensitivity
- sensitivity adjustable digital potentiometer to adjust (blue)
- modules can induction block from 0 to 3 cm
- 5 V working voltage of 3.3 V
- 5a output form the output analog voltage (0 to 5 v) B digital switch output (0 and 1)
- Has a fixed bolt hole, the work of the installation
- Small board PCB size: 3.5 cm * 1.5 cm
- The power indicator light (red) and digital switch output indicator light (green)
- Comparator USES the LM393 chips, work stability
- Three small plate interface specifications wire (4)
- 1 VCC external 3.3 V to 5 V
- 2 GND external GND
- 3 DO small plate digital output interface (0 and 1)
- 4 small AO plate analog output interface (0 to 5 v)
-
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
TEC1-12706 Thermoelectric Cooler Peltier 12vdc 6A Cooling Refrigeration Plate
-2%
Arduino, Arduino Boards & Components, Development KitsTEC1-12706 Thermoelectric Cooler Peltier 12vdc 6A Cooling Refrigeration Plate
Key Features :
- Ceramics thermoelectric Cooler semiconductor module TEC1-12706
- Small module.
- Its work is characterized by side refrigeration and side fever.
- Hot and cold on both sides of the temperature difference of 68 degrees
- Connected to the 12-volt power supply cooling piece on both sides there will be the difference in temperature, side cold side of the heat, do not long power cooler radiator, otherwise, it will cause cooler internal overheating and burning.
- Quality tested cooling cells.
- Solid-state, vibration-free, noise-free.
- Simple to install and operate.
- Fitted with 6-inch insulated leads
SKU: n/a -
Arduino Boards & Components, Arduino Components, Manual & Remote Start Units, Microcontroller, ICs etc.
TP4056 type-C Lithium Battery Charging Board
-10%
Arduino Boards & Components, Arduino Components, Manual & Remote Start Units, Microcontroller, ICs etc.TP4056 type-C Lithium Battery Charging Board
- Inputs with Type C female, can be directly input to do with the phone charger rechargeable lithium battery,
- And still retains the input voltage wiring pads, can be very convenient DIY
- Input voltage: 5V
- Charging cut-off voltage: 4.2V ± 1%
- Maximum charge current: 1000mA
- Battery over-discharge protection voltage: 2.5V
- Battery overcurrent protection current: 3A
- Board size: 2.6 * 1.7CM
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
TP4056- Micro USB Li-ion Battery Charging Board With Current Protection Bms
-20%
Arduino, Arduino Boards & Components, Development KitsTP4056- Micro USB Li-ion Battery Charging Board With Current Protection Bms
Key Features
- Microcontroller : Atmel SAM3X8E ARM Cortex-M3
- CPU: 32-Bit
- Digital I/O: Pins54
- PWM Output: 12
- PWM Output: 12
- Analog Input: 12
- Analog Input: 12
- Flash Memory (Program Memory): 512 KB
- SRAM96KB (two banks: 64KB and 32KB)
- Operating Voltage: 3.3V
- Input Voltage: 7-12 V
- Oscillator up to 84 MHz
- Arduino Due is open-source hardware! You can build your own board using the following files
- Click Here to Download Open Source Arduino Software
- EAGLE FILES IN .ZIP
- SCHEMATICS
- FRITZING IN .FZPZ
- BOARD SIZE .IN
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Tpm10 Digital Thermometer Temperature Sensor Tester Meter Fy-10 With Metal Sensor
-5%
Arduino, Arduino Boards & Components, Development KitsTpm10 Digital Thermometer Temperature Sensor Tester Meter Fy-10 With Metal Sensor
Key Features :
- LCD display.
- High accuracy.
- This thermometer can also be used to measure object temperature (baby milk, food, bath water) or ambient temperature.
- Waterproof probe, easy to remove.
- Powered by 2 x 1.5v LR44 button cell.
- Comes with a probe that is easy to use.
- Perfect for use in incubators, brooders, homebrew room at any other place, the monitoring of temperature and humidity required.
SKU: n/a
