Unbeatable Offer

UT136+ Series Digital Multimeters
₨ 4,400.00-
Arduino, Arduino Boards & Components, Development Kits
DRV8825 Stepper Motor Driver With Aluminum Heat Sink
-3%
Arduino, Arduino Boards & Components, Development KitsDRV8825 Stepper Motor Driver With Aluminum Heat Sink
?Key Features :
-
-
- Model:?DRV8825
- Supply Voltage:?8.2 ? 42 VDC.
- Current Capacity :?2.2A max(24V).
- Continuous current per phase:?1.5 A.
- Minimum Logic voltage:?2.5V.
- Maximum Logic Voltage:?5V.
- Microstep resolutions:?full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions?: 15 x 20 mm.
- Weight:?4 gm.
- Microstep resolutions:?full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Adjustable current control lets you set the maximum current output with a potentiometer. Hence lets you use voltages above your stepper motor?s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45?V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3?V and 5?V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2?oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
-
SKU: n/a -
-
Electronic Governors
Cummins 3408324 Generator Engine Actuator
- Model: 3408324
- Type: Normally Closed,0-300 KW
- Compatible EFC: 3044196
- Applicable Genset: NTA855
- Particular for PT Pump
- Working stroke: 23
- Internal installing model
- Rated voltage: 12 V; 24 V
- Response Time: 20 ms
- Weight: 0.86 kg
- Suitable for wherewith good working environment, frequently load change and the high requirement to frequency stabilization
- 3408324 applicable to generator set lower than 300 KW, work with normally closed controller
- Package Weight: 1.0 kg
- Package Size: 11.0 x 11.0 x 12.0 cm(4.3 x 4.3 x 4.7 inch)
SKU: n/a -
Auto Transfer Switches (ATS), Genset Products
DKG171 Auto Transfer Switch
Key Features
- The DKG-171 is a microprocessor-controlled unit
- Designed to monitor the 3-phase mains voltages
- Makes changeover of both generator and mains contactors
- Genset& Mains low voltages can be manually adjusted
- Small dimensions (72x72x52mm)
- Low cost
- Click Here To Download DKG171 User Manual
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
LED Traffic Light Module 5v Digital Signal Output Light Emitting Module
-6%
Arduino, Arduino Boards & Components, Development KitsLED Traffic Light Module 5v Digital Signal Output Light Emitting Module
?Key Features :
-
-
- Independent interface:
- The light-emitting module controls the red, yellow, and green lights separately, a total of four independent interfaces.
- Fast response:
- The light-emitting module can respond super fast, with strong anti-interference ability and high-cost performance.
- Good performance:
- The light-emitting module has ultra-low energy consumption, long transmission distance, and is very reliable.
- Independent interface:
-
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
Proximity Sensor E18-D80NK Infrared Yellow NPN-NO with cable
-2%
Arduino, Arduino Boards & Components, Development KitsProximity Sensor E18-D80NK Infrared Yellow NPN-NO with cable
?Key Features :
- Sensor Type:?Inductive
- Sensing distance: 0.079″ (2mm)
- Output Type😕 NPN-NO, 3-Wire
- Response Frequency:?1.5kHz
- Shielding: Shielded
- Material:?Nickel-Plated Brass
- Voltage: 10V ~ 40V
- Termination style:?Cable leads
- Operating Temperature: -40?C ~ 85?C
- Package/case: Cylinder, Threaded – M12
- Ingress Protection:?IP67
- Indicator: LED
SKU: n/a -
-
Arduino, Arduino Boards & Components, Development Kits
Mb102 Breadboard Power Supply Module 3.3v5v For Arduino Solderless Bread Board
-5%
Arduino, Arduino Boards & Components, Development KitsMb102 Breadboard Power Supply Module 3.3v5v For Arduino Solderless Bread Board
?Key Features :
- Breadboard power supply module, compatible with 5V, 3.3V.
- Apply to MB102 breadboard
- Input voltage: 6.5-12 V (DC) or USB power supply
- Output voltage: 3.3V/5V can switch over
- Maximum output current: <700 ma
- Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V
- On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use.
- Size: 53 x 32 x 23 mm.
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
DHT22
?Key Features :
- High precision
- Capacitive type
- Full range temperature compensated
- Relative humidity and temperature measurement
- Calibrated digital signal
- Outstanding long-term stability
- Extra components not needed
- Long transmission distance
- Low power consumption
- 4 pins packaged and fully interchangeable
SKU: n/a
-
Arduino, Arduino Boards & Components, Development Kits
Arduino 28byj48 5v Stepper Motor With Uln2003 Driver
-3%
Arduino, Arduino Boards & Components, Development KitsArduino 28byj48 5v Stepper Motor With Uln2003 Driver
Key Features :
- Model : 28BYJ-48
- Number of Phase : 4
- Speed Variation Ratio : 1/64
- Stride Angle : 5.625? /64
- Rated voltage : DC [5v – 12v]
- DC resistance : 5v: 60??7%(25?); 12v: 130??7%(25?)
- Frequency : 100Hz
- Idle In-traction Frequency : > 600Hz
- Idle Out-traction Frequency : > 1000Hz
- In-traction Torque >34.3mN.m(120Hz)
- Self-positioning Torque : 5v: >29.3mN.m; 12v: >42.1mN.m
- Friction torque : 600-1200 gf.cm
- Pull in torque : 300 gf.cm
- Insulated resistance >10M?(500V)
- Insulated electricity power : 600VAC/1mA/1s
- Insulation grade : A
- Rise in Temperature <40K(120Hz)
- Noise <35dB(120Hz,No load,10cm)
SKU: n/a -
Genset Products, Manual & Remote Start Units
DSE3110 Manual & Auto Genset Controller
Key Features
- Back-lit icon LCD display
- Front panel editing
- LED and LCD alarm indication
- Power Save mode
- PC configurable
- 6 Digital inputs
- 4 Outputs (2 configurable)
- Configurable timers and alarms
- Remote Start input
- Generator voltage display
- Generator frequency display
- Battery voltage display
- Engine speed display
- Hours counter
- Engine pre-heat
- Click Here To Download DSE3110 User Manual
- Click Here To Download DSE3110 Data Sheet
SKU: n/a -
Auto Transfer Switches (ATS), Automatic Mains Failure Units (AMF), Genset Products, Manual & Remote Start Units
D200 Advanced Genset Controller
-25%
Auto Transfer Switches (ATS), Automatic Mains Failure Units (AMF), Genset Products, Manual & Remote Start UnitsD200 Advanced Genset Controller
Key Features
- AMF unit with uninterrupted transfer
- ATS unit with uninterrupted transfer
- Remote start controller
- Manual start controller
- Engine controller
- Waveform display of V & I
- Harmonic analysis of V & I
- CTs at genset or load side
- Click Here To Download D200 User Manual
SKU: n/a -
Auto Transfer Switches (ATS), Automatic Mains Failure Units (AMF), Genset Products, Manual & Remote Start Units
D300 Advanced Genset Controller
-17%
Auto Transfer Switches (ATS), Automatic Mains Failure Units (AMF), Genset Products, Manual & Remote Start UnitsD300 Advanced Genset Controller
Key Features
- AMF unit with uninterrupted transfer
- ATS unit with uninterrupted transfer
- Remote start controller
- Manual start controller
- Engine controller
- Remote display & control unit
- Waveform display of V & I
- Harmonic analysis of V & I
- CTs at Genset or load side
- Click Here To Download D300 User Manual
SKU: n/a
-
Arduino, Arduino Boards & Components, Development Kits
Proximity Sensor E18-D80NK Infrared Yellow NPN-NO with cable
-2%
Arduino, Arduino Boards & Components, Development KitsProximity Sensor E18-D80NK Infrared Yellow NPN-NO with cable
?Key Features :
- Sensor Type:?Inductive
- Sensing distance: 0.079″ (2mm)
- Output Type😕 NPN-NO, 3-Wire
- Response Frequency:?1.5kHz
- Shielding: Shielded
- Material:?Nickel-Plated Brass
- Voltage: 10V ~ 40V
- Termination style:?Cable leads
- Operating Temperature: -40?C ~ 85?C
- Package/case: Cylinder, Threaded – M12
- Ingress Protection:?IP67
- Indicator: LED
SKU: n/a -
Single/Full Color (RGB) Panels/Modules, SMD Screens & Tickers
Green P10 Single Color Outdoor SMD Module For Tickers
-10%
Single/Full Color (RGB) Panels/Modules, SMD Screens & TickersGreen P10 Single Color Outdoor SMD Module For Tickers
Key Features
- Green P10 Single Color SMD Module For Tickers
- Full outdoor: IP64
- Size (W x H): 320 x 160 mm (320 x 160cm), 12.6 x 6.3 Inch
- Resolution (W x H): 32 x 16 = 512
- HUB Signal: HUB12
- Volt: 5v DC
- Brightness: 4500 cdm (nits)
- LED: DIP 5mm
- Accessories: Data Wire, Power Cable, 4-Magnets
- Can work with control card: U6A, U6B, U60, W60, U61, U62, U64, U6BN, WLP-XUA2, WLP-XUB1, etc.
- The display can Show: Text, Animation word, Time, Count, Lunar calendar
- Support simple animation characters
- Click Here to Download HD-U6A Software HD2018
SKU: n/a -
Genset Products, Manual & Remote Start Units
DSE5210 AMF Controller
Key Features
- Automatic start
- Automatic mains (utility) failure
- detection (DSE5220 only)
- Automatic load transfer
- Configurable inputs
- Configurable outputs
- Configurable alarms & timers
- Digital inputs
- Analogue inputs
- Back-lit character LCD display
- Engine protection
- Front panel mounting
- PC configurable
- Front panel programming
- Remote monitoring
- Engine history event log
- LED alarm indication
- LCD alarm indication
- SMS messaging
- Hid till lit alarm icons
- Engine exercise mode
- Magnetic pick-up
- Click Here To Download DSE5210 Operators Manual
- Click Here To Download DSE5210 Data Sheet
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
A4988 A4988 Stepper Motor Driver
?Key Features :
-
- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 ? 5.5V .
- Automatic current decay mode detection/choice.
- Mixed with slow current decay mode.
- The low power dissipation of synchronous rectifier.
- Internal UVLO(ultra voltage lockout).
- Crossover current protection.
- Thermal shutdown circuit.
- Ground fault protection.
- Loading and short circuit protection.
- The optional five-step mode: full, 1/2, 1/4, 1/8 and 1/16.
SKU: n/a -
-
Genset Products, Manual & Remote Start Units
DSE3110 Manual & Auto Genset Controller
Key Features
- Back-lit icon LCD display
- Front panel editing
- LED and LCD alarm indication
- Power Save mode
- PC configurable
- 6 Digital inputs
- 4 Outputs (2 configurable)
- Configurable timers and alarms
- Remote Start input
- Generator voltage display
- Generator frequency display
- Battery voltage display
- Engine speed display
- Hours counter
- Engine pre-heat
- Click Here To Download DSE3110 User Manual
- Click Here To Download DSE3110 Data Sheet
SKU: n/a -
Arduino, Arduino Boards & Components, Arduino Components, Development Kits, Thermometer
W1209 Temperature Control Switch
-33%
Arduino, Arduino Boards & Components, Arduino Components, Development Kits, ThermometerW1209 Temperature Control Switch
Key Features
- Low cost yet highly functional thermostat controller
- Intelligently controls power to most types of electrical device
- Comes with high accuracy NTC temperature sensor
- it has an embedded micro-controller no programming knowledge is required
- 3 tactile switches allow for configuring various parameters including on & off trigger temperatures
- On board relay can switch up to a maximum of 240V AC at 5A or 14V DC at 10A
- The current temperature is displayed in degrees Centigrade via its 3 digit seven segment display
- The current relay state is indicated by an on board LED
- Click Here to Download W1209 User Manual
SKU: n/a -
1-phase Inverters, Arduino Boards & Components, Capacitors, i) Resistor, Capacitor, Inductor, Transistor etc., Solar Inverters/ Chargers
Aluminum Electrolytic Capacitor 470UF/450V 30x45mm
-55%
1-phase Inverters, Arduino Boards & Components, Capacitors, i) Resistor, Capacitor, Inductor, Transistor etc., Solar Inverters/ ChargersAluminum Electrolytic Capacitor 470UF/450V 30x45mm
Key Features
- Built to the toughest international standards for capacitors
- Colors may vary slightly due to different monitors and different photo shooting conditions.
- Photo does not show the actual size. See the description for size details.
- Marker code on every electrolytic capacitor, and with a lable mark capacitor value, easy to distinguish
- Compact, lightweight, and highly reliable capacitor
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
TEC1-12706 Thermoelectric Cooler Peltier 12vdc 6A Cooling Refrigeration Plate
-2%
Arduino, Arduino Boards & Components, Development KitsTEC1-12706 Thermoelectric Cooler Peltier 12vdc 6A Cooling Refrigeration Plate
?Key Features :
- Ceramics thermoelectric Cooler semiconductor module TEC1-12706
- Small module.
- Its work is characterized by side refrigeration and side fever.
- Hot and cold on both sides of the temperature difference of 68 degrees
- Connected to the 12-volt power supply cooling piece on both sides there will be the difference in temperature, side cold side of the heat, do not long power cooler radiator, otherwise, it will cause cooler internal overheating and burning.
- Quality tested cooling cells.
- Solid-state, vibration-free, noise-free.
- Simple to install and operate.
- Fitted with 6-inch insulated leads
SKU: n/a
Products Grid
-
Electrical Instruments, Multimeters, Tools & Hardware
UNI-T UT201+ Digital Clamp Multimeter True RMS Clamp Meter
-10%
Electrical Instruments, Multimeters, Tools & HardwareUNI-T UT201+ Digital Clamp Multimeter True RMS Clamp Meter
Key Features
- AC current
- AC/DC voltage
- Resistance
- Continuity test
- Diode test.
- True RMS measurement.
- Audiovisual NCV detection.
- Large LCD.
- Full-featured false detection protection for up to 600 V energy surges; overvoltage and overcurrent alarm functions.
- The power consumption of the meter is about 1.8 mA.
- The circuit has an automatic power-saving function.
- The consumption in the sleep state is <11 μA, which extends the battery life to 400 hours.
- Low battery indication.
- Automatic power of after 15 of no-operation (function can be turned off).
- Data hold function.
- Max/Min mode.
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
TP4056- Micro USB Li-ion Battery Charging Board With Current Protection Bms
-20%
Arduino, Arduino Boards & Components, Development KitsTP4056- Micro USB Li-ion Battery Charging Board With Current Protection Bms
Key Features
- Microcontroller : Atmel SAM3X8E ARM Cortex-M3
- CPU: 32-Bit
- Digital I/O: Pins54
- PWM Output: 12
- PWM Output: 12
- Analog Input: 12
- Analog Input: 12
- Flash Memory (Program Memory): 512 KB
- SRAM96KB (two banks: 64KB and 32KB)
- Operating Voltage: 3.3V
- Input Voltage: 7-12 V
- Oscillator up to 84 MHz
- Arduino Due is open-source hardware! You can build your own board using the following files
- Click Here to Download Open Source Arduino Software
- EAGLE FILES IN .ZIP
- SCHEMATICS
- FRITZING IN .FZPZ
- BOARD SIZE .IN
SKU: n/a
Crazy Discounts
-
Automatic Voltage Regulators (AVRs)
AVR EA04C Generator Automatic Voltage Regulator
Key Features
- Sensing & power Input: Voltage 160 ~ 265 / 300 ~ 550VAC DIP switch selectable
- Frequency: 45 / 55 Hz, selectable
- Output Voltage: Max. 63 VDC @ 240 VAC input
- Current: Continuous 4A Intermittent 7A for 60 sec.
- Resistance: Min. 15 ohm Max. 100 ohm
- Voltage Regulation: < 1% ( with 4% engine governing )
- Voltage Build-up: Residual voltage at AVR terminal > 5 VAC
- Dimensions: 101mm L * 69mm W * 47.3mm H
- Weight: 175 g 2%
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
ESP32+cp2102 Wroom Esp32 Wifi Based Microcontroller Development Board Nodemcu
-2%
Arduino, Arduino Boards & Components, Development KitsESP32+cp2102 Wroom Esp32 Wifi Based Microcontroller Development Board Nodemcu
?Key Features :
-
- 100% brand new and high quality.
- ESP32 is already integrated antenna and RF balun,power amplifier,low-noise amplifiers,filters,and power management module.
- The entire solution takes up the least amount of printed circuit board area.
- This board is used with 2.4 GHz dual-mode Wi-Fi and Bluetooth chips by TSMC 40nm low power technology,power and RF properties best,which is safe,reliable,and scalable to a variety of applications.
- High performance-price ratio.
- Small volume,easily embeded to other products.
- Strong function with support LWIP protocol,Freertos.
- Supporting three modes:AP,STA,and AP+STA.
- Supporting Lua program,easily to develop.
SKU: n/a -
-
Auto Transfer Switches (ATS), Automatic Mains Failure Units (AMF), Genset Products, Manual & Remote Start Units
D300 Advanced Genset Controller
-17%
Auto Transfer Switches (ATS), Automatic Mains Failure Units (AMF), Genset Products, Manual & Remote Start UnitsD300 Advanced Genset Controller
Key Features
- AMF unit with uninterrupted transfer
- ATS unit with uninterrupted transfer
- Remote start controller
- Manual start controller
- Engine controller
- Remote display & control unit
- Waveform display of V & I
- Harmonic analysis of V & I
- CTs at Genset or load side
- Click Here To Download D300 User Manual
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Cable for UNO
?Key Features :
- Fully compatible with the PC.
- Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
- Aluminum under mold shield helps meet FCC requirements on KMI/RFI interference.
- Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
Water Pump 5V
?Key Features :
- Operating Current : 130 ~ 220mA
- Operating Voltage : 2.5 ~ 6V
- Flow Rate : 80 ~ 120 L/H
- Maximum Lift : 40 ~ 110 mm
- Driving Mode : DC, Magnetic Driving
- Continuous Working Life : 500 hours
- Material : Engineering Plastic
- Outlet Outside Diameter : 7.5 mm
- Outlet Inside Diameter : 5 mm
SKU: n/a -
Arduino, Arduino Boards & Components, Development Kits
DRV8825 Stepper Motor Driver With Aluminum Heat Sink
-3%
Arduino, Arduino Boards & Components, Development KitsDRV8825 Stepper Motor Driver With Aluminum Heat Sink
?Key Features :
-
-
- Model:?DRV8825
- Supply Voltage:?8.2 ? 42 VDC.
- Current Capacity :?2.2A max(24V).
- Continuous current per phase:?1.5 A.
- Minimum Logic voltage:?2.5V.
- Maximum Logic Voltage:?5V.
- Microstep resolutions:?full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions?: 15 x 20 mm.
- Weight:?4 gm.
- Microstep resolutions:?full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Adjustable current control lets you set the maximum current output with a potentiometer. Hence lets you use voltages above your stepper motor?s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45?V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3?V and 5?V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2?oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
-
SKU: n/a -
-
-
Uncategorized
Indoor and Outdoor Temperature & Humidity Meter with High-Visibility P10 SMD Display
Key Features & Technical Specifications
-
High-Visibility Display: 32×16 resolution P10 SMD module provides superior brightness and clarity for excellent long-distance readability.
-
Rugged & Durable Build: Features a sturdy black aluminum casing that is completely rust-proof, ensuring longevity in diverse environments.
-
Dual-Purpose Design: Certified for reliable performance in both indoor and outdoor installations.
-
Universal Power: Simple plug-and-play operation on standard 220V AC.
-
Optimal Size: Compact dimensions of 13.5″ (W) x 6.75″ (H) x 2.1″ (D) offer a perfect balance of prominent display and space efficiency.
-
Superior Accuracy: Utilizes imported sensors and components for consistent, precise readings of temperature and humidity.
SKU: n/a -
Best Sellers
Recently Added
Indoor and Outdoor Temperature & Humidity Meter with High-Visibility P10 SMD Display

Indoor and Outdoor Temperature & Humidity Meter with High-Visibility P10 SMD Display
Key Features & Technical Specifications
High-Visibility Display: 32×16 resolution P10 SMD module provides superior brightness and clarity for excellent long-distance readability.
Rugged & Durable Build: Features a sturdy black aluminum casing that is completely rust-proof, ensuring longevity in diverse environments.
Dual-Purpose Design: Certified for reliable performance in both indoor and outdoor installations.
Universal Power: Simple plug-and-play operation on standard 220V AC.
Optimal Size: Compact dimensions of 13.5″ (W) x 6.75″ (H) x 2.1″ (D) offer a perfect balance of prominent display and space efficiency.
Superior Accuracy: Utilizes imported sensors and components for consistent, precise readings of temperature and humidity.
UT18D Uni-T Voltage and Continuity Tester
UT18B Voltage Detector Tester
Key Features:
Solder Paste – 500g | High-Quality Soldering Paste Sn63Pb37

Solder Paste – 500g | High-Quality Soldering Paste Sn63Pb37
UT181A True RMS Datalogging Multimeter
UT71E Series Intelligent Digital Multimeters

UT71E Series Intelligent Digital Multimeters
UT71C Series Intelligent Digital Multimeters

UT71C Series Intelligent Digital Multimeters
UT71A Series Intelligent Digital Multimeters

UT71A Series Intelligent Digital Multimeters
UT60BT Series Digital Multimeters
UT60EU Series Digital Multimeters










































